Airworthiness Directives; Boeing Model 757-200, -200CB, and -200PF Series Airplanes

로컬 자동 번역 · 원본 출처 언어

요약

The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 757-200, -200CB, and -200PF series airplanes. This AD requires an inspection of each trailing edge flap transmission assembly to determine the part number and serial number, and related investigative and corrective actions and part marking if necessary. This AD results from a report indicating that cracked flap transmission output gears have been discovered during routine overhaul of the trailing edge flap transmission assemblies. We are issuing this AD to prevent an undetected flap skew, which could result in a flap loss, damage to adjacent airplane systems, and consequent reduced controllability of the airplane.

원본 출처 언어: Federal Register — Federal Aviation Administration원문 발표 열기 →

기업 추가

비즈니스 소스를 모니터링하고 Business Communicator의 기업과 프로필을 연결합니다.

무료 기업 프로필 만들기 Business Maps에서 기업 찾기 →

무료 기업 프로필 만들기 →

Airworthiness Directives; Airbus SAS Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A319-111, -112, -113, -114, -115, -131, -132, and -133 airplanes; Model A320 series airplanes; and Model A321-211, - 212, -213, -231, -232, -251N, -251NX, -252N, -252NX, -253N, -253NX, - 271N, -271NX, -272N, and -272NX airplanes. This AD was prompted by a review of the cold working process on the assembly line that detected a deviation to the manufacturing process. This AD requires repetitive inspections for the nominal design condition of the fastener holes in the pressure deck membrane to center wing box attachment and, as applicable, an inspection for cracking at the affected area and corrective actions. The FAA is issuing this AD to address the unsafe condition on these products.

요약 읽기 →

비즈니스 · 2026. 5. 22.

Airworthiness Directives; Embraer S.A. (Type Certificate Previously Held by Yaborã Indústria Aeronáutica S.A.; Embraer S.A.) Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain Embraer S.A. Model ERJ 190-100 ECJ airplanes. This AD was prompted by a manufacturing quality escape concerning certain overheat detection system (ODS) sensing elements. This AD requires a detailed inspection of certain ODS sensing elements of the airplane bleed lines and replacement, if necessary. This AD also prohibits the installation of affected parts. The FAA is issuing this AD to address the unsafe condition on these products.

요약 읽기 →

비즈니스 · 2026. 5. 22.

Airworthiness Directives; Airbus SAS Airplanes

The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A330-200 series airplanes; Model A330-200 Freighter series airplanes; Model A330-300 series airplanes; and Model A330-841 and -941 airplanes. This AD was prompted by a report of an in-service event and relevant investigation which found that, under specific conditions, a dormant failure of a standby fuel pump could lead to a certain amount of fuel being trapped in the aft section of the inner tank that would be unusable. This AD requires repetitive operational checks of the standby fuel pumps and corrective actions and limits the installation of affected parts under certain conditions. The FAA is issuing this AD to address the unsafe condition on these products.

요약 읽기 →

비즈니스 · 2026. 5. 14.

Airworthiness Directives; ATR-GIE Avions de Transport Régional Airplanes

The FAA is adopting a new airworthiness directive (AD) for all ATR--GIE Avions de Transport R[eacute]gional Model ATR42-200, -300, and -320 airplanes. This AD was prompted by a report of an occurrence of a flap asymmetry detector and flap interconnection shaft having worn splines and not engaging mechanically. This AD requires a special detailed inspection (SDI) of the affected flap asymmetry detection mechanism, and applicable corrective actions. The FAA is issuing this AD to address the unsafe condition on these products.

요약 읽기 →

비즈니스 · 2026. 5. 14.

Airworthiness Directives; Airbus SAS Airplanes

The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A350-941 and -1041 airplanes. This AD was prompted by the obsolescence of the clamp holding in place the oxygen generator in the container and introduction of a new clamp from another manufacturer with different locking torque specifications, which were not properly reflected in Airbus documentation. This AD requires replacing each affected part, prohibits accomplishing maintenance actions using certain versions of a maintenance procedure task, and also prohibits the installation of affected parts. The FAA is issuing this AD to address the unsafe condition on these products.

요약 읽기 →

비즈니스 · 2026. 5. 14.

Airworthiness Directives; Dassault Aviation Airplanes

The FAA is superseding Airworthiness Directive (AD) 2023-22- 05, which applied to certain Dassault Aviation Model FAN JET FALCON and FAN JET FALCON SERIES C, D, E, F, and G airplanes. AD 2023-22-05 required revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. Since the FAA issued AD 2023-22-05, the FAA has determined that new or more restrictive airworthiness limitations are necessary. This AD continues to require certain actions in AD 2023-22-05 and requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. The FAA is issuing this AD to address the unsafe condition on these products.

요약 읽기 →