BN Business News
Business Maps⌕ Rechercher dans Business News
Ajouter votre entreprise →
Cette traduction est en cours de préparation. En attendant, nous affichons temporairement la version originale en anglais.

Entreprise · 06/09/20051 min de lecture

Airworthiness Directives; Boeing Model 737-100, -200, -200C, and -300 Series Airplanes

Traduction automatique locale · Langue originale de la source

Résumé

The FAA is adopting a new airworthiness directive (AD) for certain Boeing Model 737-100, -200, -200C, and -300 series airplanes. This AD requires repetitive detailed inspections to detect discrepancies of the retaining pin lugs on the support fitting of the main landing gear (MLG) beam, and rework of the support fitting, or replacement of the fitting if necessary. This AD is prompted by reports of discrepancies of the lugs. We are issuing this AD to prevent separation of the support beam of the MLG from the rear spar, which could cause cracking of the MLG support fitting and a consequent leak in the wing fuel tank or collapse of the MLG.

Langue originale de la source: Federal Register — Federal Aviation AdministrationOuvrir le communiqué original →

Explorer les analyses

Analyses business →
6

Entreprise · 14/05/2026

Airworthiness Directives; Airbus SAS Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A319-111, -112, -113, -114, -115, -131, -132, and -133 airplanes; Model A320 series airplanes; and Model A321-211, - 212, -213, -231, -232, -251N, -251NX, -252N, -252NX, -253N, -253NX, - 271N, -271NX, -272N, and -272NX airplanes. This AD was prompted by a review of the cold working process on the assembly line that detected a deviation to the manufacturing process. This AD requires repetitive inspections for the nominal design condition of the fastener holes in the pressure deck membrane to center wing box attachment and, as applicable, an inspection for cracking at the affected area and corrective actions. The FAA is issuing this AD to address the unsafe condition on these products.

Lire le résumé →

Entreprise · 22/05/2026

Airworthiness Directives; Airbus SAS Airplanes

The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A330-200 series airplanes; Model A330-200 Freighter series airplanes; Model A330-300 series airplanes; and Model A330-841 and -941 airplanes. This AD was prompted by a report of an in-service event and relevant investigation which found that, under specific conditions, a dormant failure of a standby fuel pump could lead to a certain amount of fuel being trapped in the aft section of the inner tank that would be unusable. This AD requires repetitive operational checks of the standby fuel pumps and corrective actions and limits the installation of affected parts under certain conditions. The FAA is issuing this AD to address the unsafe condition on these products.

Lire le résumé →

Entreprise · 22/05/2026

Airworthiness Directives; Embraer S.A. (Type Certificate Previously Held by Yaborã Indústria Aeronáutica S.A.; Embraer S.A.) Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain Embraer S.A. Model ERJ 190-100 ECJ airplanes. This AD was prompted by a manufacturing quality escape concerning certain overheat detection system (ODS) sensing elements. This AD requires a detailed inspection of certain ODS sensing elements of the airplane bleed lines and replacement, if necessary. This AD also prohibits the installation of affected parts. The FAA is issuing this AD to address the unsafe condition on these products.

Lire le résumé →

Entreprise · 22/05/2026

Airworthiness Directives; Bombardier, Inc., Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain Bombardier, Inc., Model BD-700-1A10 and BD-700-1A11 airplanes. This AD was prompted by reports that inappropriate tooling was used to torque the bolts securing the baggage door stop fittings, which may have resulted in an improper torque condition. This AD requires performing a torque check of affected bolts and re-torquing, re- installing, or replacing affected bolts and nuts as applicable. The FAA is issuing this AD to address the unsafe condition on these products.

Lire le résumé →

Entreprise · 21/05/2026

Airworthiness Directives; Bell Textron Canada Limited Helicopters

The FAA is adopting a new airworthiness directive (AD) for certain Bell Textron Canada Limited (BTCL) Model 407 helicopters. This AD was prompted by a determination that chafing can occur at various locations on the electrical harnesses located in the aircraft instrument panel area. This AD requires a one-time detailed visual inspection of the electrical harnesses for chafing and corrective actions if necessary. This AD also requires rotation of the backshell cast housing of connectors of the lower engine airframe unit and installation of a wire harness bracket and support, and for certain helicopters, installation of a wire bundle sleeve. The FAA is issuing this AD to address the unsafe condition on these products.

Lire le résumé →

Entreprise · 14/05/2026

Airworthiness Directives; ATR-GIE Avions de Transport Régional Airplanes

The FAA is adopting a new airworthiness directive (AD) for all ATR--GIE Avions de Transport R[eacute]gional Model ATR42-200, -300, and -320 airplanes. This AD was prompted by a report of an occurrence of a flap asymmetry detector and flap interconnection shaft having worn splines and not engaging mechanically. This AD requires a special detailed inspection (SDI) of the affected flap asymmetry detection mechanism, and applicable corrective actions. The FAA is issuing this AD to address the unsafe condition on these products.

Lire le résumé →