BN Business News
Business Maps⌕ Rechercher dans Business News
Ajouter votre entreprise →
Cette traduction est en cours de préparation. En attendant, nous affichons temporairement la version originale en anglais.

Entreprise · 15/11/20051 min de lecture

Airworthiness Directives; Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) Airplanes

Traduction automatique locale · Langue originale de la source

Résumé

The FAA proposes to adopt a new airworthiness directive (AD) for certain Bombardier Model CL-600-2B19 (Regional Jet Series 100 & 440) airplanes. This proposed AD would require replacing the Camloc fasteners on the sidewall of the center pedestal. This proposed AD results from reports of the Camloc fasteners on the sidewall of the center pedestal disengaging and interfering with an inboard rudder pedal. We are proposing this AD to prevent these fasteners from disengaging and interfering with an inboard rudder pedal, which could reduce directional controllability of the airplane.

Langue originale de la source: Federal Register — Federal Aviation AdministrationOuvrir le communiqué original →

Explorer les analyses

Analyses business →
6

Entreprise · 15/05/2026

Airworthiness Directives; Diamond Aircraft Industries Inc. Airplanes

The FAA proposes to adopt a new airworthiness directive (AD) for certain Diamond Aircraft Industries Inc. (DAI) Model DA20-C1 airplanes. This proposed AD was prompted by a report of a certain emergency locator transmitter (ELT) not activating due to a missing jumper wire. This proposed AD would require a continuity inspection of the D-sub connector of the Artex ELT 1000 and, if necessary, corrective actions. The FAA is proposing this AD to address the unsafe condition on these products.

Lire le résumé →

Entreprise · 22/05/2026

Airworthiness Directives; Airbus Helicopters

The FAA proposes to supersede Airworthiness Directive (AD) 2023-25-14, which applies to certain Airbus Helicopters Model EC130T2 helicopters. AD 2023-25-14 revises the procedures for inspecting the vibration level on the tail rotor drive shaft and, depending on these results, requires replacing certain parts. Since the FAA issued AD 2023-25-14, the manufacturer developed a modification of the rear drive shaft, sliding flange and equipped splined sleeve. This proposed AD would require installing this modification and repetitively inspecting the vibration level of the tail rotor drive shaft. This proposed AD would also prohibit the installation of certain parts and prohibit the performance of a balance correction unless certain requirements are met. The FAA is proposing this AD to address the unsafe condition on these products.

Lire le résumé →

Entreprise · 20/05/2026

Airworthiness Directives; Airbus SAS Airplanes

The FAA proposes to adopt a new airworthiness directive (AD) for all Airbus SAS Model A330-841 and Model A330-941 airplanes. This proposed AD was prompted by reports of crack findings on the sloping rib. This proposed AD would require a repetitive inspection of the external surface of each sloping rib and each slat 1 inboard seal, and applicable corrective actions. The FAA is proposing this AD to address the unsafe condition on these products.

Lire le résumé →

Entreprise · 15/05/2026

Airworthiness Directives; Airbus Helicopters

The FAA proposes to adopt a new airworthiness directive (AD) for certain Airbus Helicopters Model AS350B, AS350BA, AS350B1, AS350B2, AS350B3, AS350D, EC130B4, and EC130T2 helicopters. This proposed AD was prompted by reports of an incorrectly installed engine flange on the main gear box (MGB) engine coupling. This proposed AD would require inspecting the MGB engine coupling for correct installation and, depending on the results, corrective actions. The FAA is proposing this AD to address the unsafe condition on these products.

Lire le résumé →

Entreprise · 15/05/2026

Airworthiness Directives; Stemme GmbH Gliders

The FAA proposes to adopt a new airworthiness directive (AD) for all Stemme GmbH (Stemme) Model Stemme S 12 gliders. This proposed AD was prompted by reports of fuel leaking around certain copper sealing rings within the fuel system. This proposed AD would require repetitive visual checks of the fuel system for fuel leakage, and replacement of the affected copper sealing ring. This proposed AD would also prohibit the installation of affected parts. The FAA is proposing this AD to address the unsafe condition on these products.

Lire le résumé →

Entreprise · 22/05/2026

Airworthiness Directives; Bombardier, Inc., Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain Bombardier, Inc., Model BD-700-1A10 and BD-700-1A11 airplanes. This AD was prompted by reports that inappropriate tooling was used to torque the bolts securing the baggage door stop fittings, which may have resulted in an improper torque condition. This AD requires performing a torque check of affected bolts and re-torquing, re- installing, or replacing affected bolts and nuts as applicable. The FAA is issuing this AD to address the unsafe condition on these products.

Lire le résumé →