Airworthiness Directives; Airbus SAS Airplanes

ビジネス · 2026/5/14

Airworthiness Directives; Airbus SAS Airplanes

The FAA is superseding Airworthiness Directive (AD) 2025-03- 07, which applied to certain Airbus SAS Model A318, A319, and A320 series airplanes; and Model A321-111, -112, -131, -211, -212, -213, - 231, -232, -251N, -252N, -253N, -271N, -272N, -251NX, -252NX, -253NX, - 271NX, and -272NX airplanes. AD 2025-03-07 required revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. Since the FAA issued AD 2025-03-07, the FAA has determined that new or more restrictive airworthiness limitations are necessary. This AD continues to require certain actions in AD 2025-03-07 and requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, and expands the applicability. The FAA is issuing this AD to address the unsafe condition on these products.

ビジネス · 2026/5/22

Airworthiness Directives; Airbus SAS Airplanes

The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A330-200 series airplanes; Model A330-200 Freighter series airplanes; Model A330-300 series airplanes; and Model A330-841 and -941 airplanes. This AD was prompted by a report of an in-service event and relevant investigation which found that, under specific conditions, a dormant failure of a standby fuel pump could lead to a certain amount of fuel being trapped in the aft section of the inner tank that would be unusable. This AD requires repetitive operational checks of the standby fuel pumps and corrective actions and limits the installation of affected parts under certain conditions. The FAA is issuing this AD to address the unsafe condition on these products.

ビジネス · 2026/5/14

Airworthiness Directives; Airbus SAS Airplanes

The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A350-941 and -1041 airplanes. This AD was prompted by the obsolescence of the clamp holding in place the oxygen generator in the container and introduction of a new clamp from another manufacturer with different locking torque specifications, which were not properly reflected in Airbus documentation. This AD requires replacing each affected part, prohibits accomplishing maintenance actions using certain versions of a maintenance procedure task, and also prohibits the installation of affected parts. The FAA is issuing this AD to address the unsafe condition on these products.

ビジネス · 2026/5/22

Airworthiness Directives; Embraer S.A. (Type Certificate Previously Held by Yaborã Indústria Aeronáutica S.A.; Embraer S.A.) Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain Embraer S.A. Model ERJ 190-100 ECJ airplanes. This AD was prompted by a manufacturing quality escape concerning certain overheat detection system (ODS) sensing elements. This AD requires a detailed inspection of certain ODS sensing elements of the airplane bleed lines and replacement, if necessary. This AD also prohibits the installation of affected parts. The FAA is issuing this AD to address the unsafe condition on these products.

ビジネス · 2026/5/22

Airworthiness Directives; Bombardier, Inc., Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain Bombardier, Inc., Model BD-700-1A10 and BD-700-1A11 airplanes. This AD was prompted by reports that inappropriate tooling was used to torque the bolts securing the baggage door stop fittings, which may have resulted in an improper torque condition. This AD requires performing a torque check of affected bolts and re-torquing, re- installing, or replacing affected bolts and nuts as applicable. The FAA is issuing this AD to address the unsafe condition on these products.

ビジネス · 2026/5/14

Airworthiness Directives; Dassault Aviation Airplanes

The FAA is superseding Airworthiness Directive (AD) 2023-22- 05, which applied to certain Dassault Aviation Model FAN JET FALCON and FAN JET FALCON SERIES C, D, E, F, and G airplanes. AD 2023-22-05 required revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. Since the FAA issued AD 2023-22-05, the FAA has determined that new or more restrictive airworthiness limitations are necessary. This AD continues to require certain actions in AD 2023-22-05 and requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. The FAA is issuing this AD to address the unsafe condition on these products.